Search results

Doing an LS Swap in my T-Type, any thoughts on going vintage air and any suggestions on where i can get one from?

Hello Gents, I'm in the process of building a Turbo LS Engine for my T-Type. I'm trying to get an idea of what every ones combo is and in one thread. I assume it will help others in the future to have one thread with everyone's combo so they can get an idea of which route to take. Could you...

Bought this to go on my Buick but decided to build a turbo LQ4 instead, hence i need a different turbo. Its still in the box sealed by precision. I don't want to open it because then it wont be "new still in the box factory sealed", not sure if that adds value but im sure it will to some buyer...

I've had this car for sale in the past but i couldn't bare to sell it but its back up for sale. Asking 15K 1987 Buick GN 66K Miles Digital Dash Power Seats Posi-Track Eric Marshal Chip Kirban Mystery Theft Deterrent System Call or Text me at 832 314 4318. No trades please. I believe I'm...

Looking for a Roller with 8 out of 10 paint and ok interior. I have a built tranny and engine ready to drop in. I dont care about the location, i'll have it shipped to Houston.

I don't prefer to have one that is all stock, i prefer to have one with tasteful mods and in the Texas area (im in Houston)

i need to ship my powermaster to Kirbans, is there a non PO box address I can ship it to? I'm Currently at the post office on stand by.

Gents, Trying to make my mind up between a jouran bearing turbo or a BB turbo. In particular, im looking to replace my TE-60 (which took a mean dump on me) with: A) 6265 or B) 6262. (not sure which turbo). For folks who have owned the same turbo with a journal bearing and BB (probably not...

This sounds like a dumb question but i'll take the hit so others who have had this questions can better understand. What does having a loose versus having a tight converter mean can you please list examples of how this relates to low, mid, and high end power and if i had a lose converter with a...

My TE 60 took a crap on me and I'm currently chatting with Bison and I have to say, what I've read about the below turbo or brand of turbo seems pretty bad ass (I have never heard of them before until Bison mentioned them). Yes they are pricey but whatever. If Bison has the below item in his...

I installed one of the RJC pully's (I think its called a crank pully but its the larger one at the far bottom) and I believe the diameter might be a tad smaller than stock because I changed out my belt with a stock replacement and not my car makes squeaks pretty loud. Any one have an idea of a...

I swapped out my 42# Injectors for 80# injectors and my new SD 2 Chip from turbo tweak and now my car starts but dies soon after. Any ideas on what it could be? We turned the fuel pressure up to 60#'s and it will barely run.

does anyone in the Houston area have a 10inch rear wheel with drag radials? I'm looking to purchase 10inch rears and was trying to figure what a set of 275/60/15's MT DR's would look like on a 10 inch wheel. Also any rub issues against both the fender and frame (my fenders are rolled by the way).

Ok so I installed my powerlogger and I updated my scanmaster to the 2.2. I still have the 5.7 chip (I'm in the process of deciding to buy the 6.1 or the SD but im leaning towards the SD chip). So when I want to make changes now do I open the powerlogger and manipulate the powerlogger or do I...

Ok I'm about to pull the trigger on purchasing a new chip (mine is outdated for my combo from my comvo with Eric) but I wanted to understand the pro's and cons of tuning using SD and tuning using the 6.1 chip (MAF). I have no clue how to tune but I have two good friend (Paul and Jeryl) who are...

I've been reading about gas tanks because I need to purchase one, between the goodman and the spectra, anyone think one is better than the other. I cant find an original GM one but then again I don't know how much better a GM gas tank is than an after market. I've been reading the old threads...

Ok so I've been reading through the different threads regarding backspacing. I need to purchase two rear wheels and I know that I want 15X10 wheels. My fenders are rolled in the back and I'm trying to decide between a 4.5" and 5" backspace. From what I gather, the 4.5 will work without...

My T-Type is in the body shop fixing some major body work and the body shop stated they need a rear trunk pan. Any Idea where I can get it from? I cant seem to find anything on the web and I also posted in the "wanted" part of this board. Thanks for all your help folks. I've been posting...

I'm fixing my car and need a rear trunk floor pan. Anyone know where I can find one or does anyone know a person who is selling one?

I was looking at purchasing some braces to stiffen up the car but do they actually make a difference? Also between the GNX style rear seat brace and the other type that looks like its made up of 4 metal bars (both are sold on kirbans sight and I think g body's (brains) sight) which is better?