Search results

DSE Front and rear lowering springs. Rears were installed for mock up and then removed. They have no miles on them. Front springs have about 5 to 700 miles tops on them. They will lower your car approximately 2 inches. Asking $300 shipped

New in box Metco driveshaft safety loop for g-body’s, part number MDL2000. $90 shipped

Brand new in box Rollmaster timing chain. $130 shipped to the lower 48 PayPal friends and family: NJLT1SS1@aol.com

MSD 8.5 Super Conductor spark plug wire set. These were purchased new, used them till I switched to the TR6 ignition with truck coils. Have about 3,000 miles on them. You get them as pictured, with MSD plug wire separators and numbers. Last pic is of the wires on my motor. $60 shipped to lower 48

Looking to improve the ride on my GN, and have adjustability in the ride height. I currently run Billsteins all around, stock springs in the rear, DSE drop springs in the front. I did this as the stock front springs were a bitch to try and reinstall, and didn't want to kill myself. Can't say I'm...

I have 2 Turbo Tweak 5.7 chips for sale. Both are for 60 lbs injectors. Top one in the pic I was running pump gas only. Chip in the bottom pic I was running pump gas and Alky, 24 to 25 psi. I think you could use either one for pump gas/Alky. $80 each shipped.

I have the following intake set up for sale: 4 inch RJC intake pipe, Z06 MAF, 9 inch long K&N air filter, and MAF Translator with adapter. Comes with hoses and clamps. This set up ran great on my stock longblock. K&N has a hole in it for the air intake temp. Pipe could us a polish. It does have...

Heated O2 sensor kit for sale, 5K Street miles on it, no race gas has been run through it. Comes with 12” 02 extension. $50 to ship to lower 48 states. Nick

AEM Wideband, comes with new 02. $150 shipped SOLD 3781 - AutoMeter Ultra-Lite Tachometer, 3 3/4 inch, never installed. I set the dip switches for a V-6. Lost one of the screws on the back cover replaced it with a different one, pick attached. 183.95 new from Summit, asking $125 shipped. SOLD...

Scanmaster for sale, $180 shipped to the lower 48. I accept PayPal, please include fees

Anyone know the part number for the slim fan on the Alradco dual fan set up? I want to replace one of my extreme fans with a slim one, as one of my front mount pipes rubs on the fan. I already tried cutting the pipe and using a coupler for more clearance. It helps, but still rubs. I am looking...

Hey Guys, I'm getting ready to reinstall my stock front coil springs. What do you use to get these things back in, without killing yourself? I was going to use a coil spring compressor that goes inside the spring to compress them a little, then jack up on the front control arm. What's the best...

Fuel system parts for sale. Racetronix 340lph and sender with 5k miles with analog sender, new fuel filter, new hoses that go from sender to stand off pipes. Asking $250 shipped. I accept PayPal, buyer covers PayPal fees.

I have my motor on a stand and I just replaced the rear main seal. I filled up the sides until it oozed out. I ended up using The Right Stuff Ultra Gray instead of black. Anybody ever use the gray? Does it matter which one is used? Nick

I have a brand-new set in the box TA V1412 hydraulic roller lifters for Buick V6. New they are $300 on TA's site. I'm looking for $280 shipped.

Accufab AFPR, approx. 2K miles on it, $75 shipped SOLD! TT 5.7 street chip, 93 octane, for 60lb injectors, $55 shipped. GM front bumper fillers. They are painted black, but prep work wasn't done well, paint bubbled and chipped off in a few spots. $100 shipped for the pair. Pics below... SOLD

Where can I buy methanol in the north New Jersey area? I'm in Morris County near Parsippany. I work in Clifton so that area works too.

These were purchased NEW from Highway Stars (NOS4GN).... Hight Output (Magnavox) coil pack, and GM ignition module D1996 - GM # 24503624. Coil goes for 39.95 new, and ICM for 199.00 new. I am looking for $200 for both, shipping included to lower 48. PayPal..... NJLT1SS1@aol.com

Hey guys, I will be doing a front brake upgrade soon and pulling off my stock spindles, so why not install new bushings and ball joints while in there. Has anyone ever replaced the front control arm bushings and ball joints? Can it be done at home, or does a shop need to remove and press the new...

1 set of front steel braided brake lines, same ones that G Body sells minus the rear line. These are new, asking $70 shipped Energy Suspension rear end bushings, also new. $35 shipped. If someone wants to purchase both, $90 shipped.