Search results

Love their sway bar on my car, I am changing over to a 9" and need new brackets. I tried phone, facebook, email etc, no response..... anything I am missing?

LQ4 6.0 turbo swap in place, battery in the trunk. Tubular front upper arms with Delrin bushings, 90/10 shocks no sway bar. Car has a nice stance, but obviously sits a bit lower in the front. Will it be mandatory to switch over to a V8 spring up front? No trans brake, just foot for launches Thanks!

Anyone happen to know how many things can cause an xfi box to have no injector lights lit up with key on or cranking? Connected to can bus and Xim feeding an LS...

We are working on a TTA, just wondering what other valve covers are the same, heard rumours of fwd 3.0l etc. Thanks

for those with th LS and 4l80 swap, I need a measurement from the back of the trans to the top of the tunnel, any reference point is fine! Trying to see what mods I need to make to the stock crossmember.... Thanks!!!

Low miles on both, work perfect. Can email pics if needed. Part number 108135 $220 shipped for the box, $35 shipped for the harness

Cody Motorsports (Chuck Leeper) has gone through these injectors, cleaned and flowed. Ready to go! $180 shipped obo

Ready to go, flowed and tested by Cody Motorsports (Chuck Leeper) Low impedance, requires modded ecm or any aftermarket ecm $190 shipped gets em! Will send them in an a hard case with foam and flow sheet.

Transplanted my ME-R system and modded ecm (no maf) with 75lb injectors into another car. Stockish new build, bb 61 turbo, alky, ported irons. Wideband after 1.5 seconds or so WOT would go under 9 afr and the car would almost shut off, half throttle was great. Leanest setting on fuel, widebrand...

Last season I transplanted my ME-R setup with 75lb injectors and wideband correction over to a milder stock build car, ported irons, stock cam, ball bearing 61 turbo, alky etc. Ac delco cr43ts plugs gapped at .32 as I always have done. Ran great at idle and half throttle. Under WOT the car would...

I sold my pan nuts with my deep pan and now need replacements for another project. Can anyone confirm the size? I measured a thread pitch of 18mm, but need to know if it is a 7 or 8mm stud.

Worked awesome on my car, mid 130's in the quarter at 19psi on my 249ci. 12.2 at 7psi lol. Only selling because I am going LS, spooled great with a PTC 9.5. Comes with a Milam gasket. Glassed flat on exhaust side for a perfect seal, new stainless studs included. Paid $1700 and put on very few...

Must be in good condition (replacing a bent one)

Everything in sig will be for sale, going to a 6.0l LS turbo setup. (Thought I would never say that....) Updates very soon with detailed pics.....thanks!

When a distributor no longer seats fully and loses contact with the oil pump, sweet colors are produced! Nothing magical about the problem, just an oops on my part lol... Only the thrust and 1 rod bearing got the beating, everything else actually looked good. Aside from the color..... Got the...

Lets hear the debate.... I have my intake off at the moment and was thinking of getting rid of my aftermarket valley pan and pcv valve/catch can setup to clean things up. I have a electric vacuum pump already plumbed to the valve covers when the car is under boost to get rid of some pressure...

Do I send my stock ecm to Bob Bailey or who is the lucky one? I think I have a bad low impedance injector driver on #1. Anyone?

Having some ME-R issues, does anyone have a phone number for either of these fellows? I have left pm's and an email for Eric. Thanks....

Anyone?

Just need the gear off of a stock cam sensor. Thanks!