Search results

  1. Chuck Leeper

    Trailering a Turbo Regal

    Why would you do it any differently than the GS? They weigh about the same. The Regal is likely about 34-3500.
  2. Chuck Leeper

    The First Comp Turbo CTRX Hubless

    I made a plate to bolt to the rear of the dr side head. It included a loop for a cable to pass thru. The cable was looped around the rear of the lower control arm mount and secured with cable clamps. No vibration transmitted, no bending of parts, no breaking of the alum accessory drive. But it...
  3. Chuck Leeper

    Scammer

    He has been "dealt with"!
  4. Chuck Leeper

    Radiator cushions

    Fits on the seam where the tank is joined to the core. Aftermkt may align with the holes/location in the core support. May not. May have to "McGuyver it" a bit.
  5. Chuck Leeper

    Rebuilding my NEW engine

    What does the sides of the rod bearings look like? Aftermkt rod may take chamfered bearings. Are these that way? Any indication of brg contact on the cheeks of the crank?
  6. Chuck Leeper

    Aviation fuel and Spool up

    At it again???:LOL:
  7. Chuck Leeper

    Rebuilding my NEW engine

    Before I bought new brgs, I'd have that crank and rods inspected for dimensions. Those brgs look like they have had dirt in them, and don't have consistent clearances, showing odd wear patterns. When you pulled it apart, did you check side clearances and crank end play? What do the mains look...
  8. Chuck Leeper

    Scammer Hammer Time

    He's been banned already, I think earlier today.
  9. Chuck Leeper

    Meanwhile, in Denver

    Already in place, in many areas.... Especially rural areas.;);)
  10. Chuck Leeper

    Meanwhile, in Denver

    Exactly correct. Paving the way for paperless money and the socialist takeover.
  11. Chuck Leeper

    runs with stock ecm, not with xfi 2.0

    if i open the file you posted with ccomWP2.051 the individual cyl table has crazy values leading me to believe its not a 2.05 setup tune Mine is 2.051. Probably should disregard what I've posted.
  12. Chuck Leeper

    runs with stock ecm, not with xfi 2.0

    You have the rpm cut set to 50. From the basic setup info: " 6.2.2 Spark Cut Rev. Limit This is an ignition rev limiter used for maximum RPM rev limiting. It is always active. If this feature is not to be used, enter a RPM value above what you will ever reach. Goto: System config, then to global...
  13. Chuck Leeper

    runs with stock ecm, not with xfi 2.0

    Post the tune and do a short data log of an attempted start. Put them in a zip file. Link up, start log, then attempt a start. Just a few seconds should suffice.
  14. Chuck Leeper

    Meanwhile, in Denver

    Another leftwing cesspool declining to shithole status..... Screw those assholes. They voted for those idiots, so live with their choices.
  15. Chuck Leeper

    And he thought....

    I recall the videos of him on a cart, riding around a course. A real shame a local wild hog hunter didn't blow his head off at 500 yds.
  16. Chuck Leeper

    AWUUNSE

    @wq^^7
  17. Chuck Leeper

    And he thought....

    https://www.foxnews.com/us/oj-simpson-dead-76-family-says he got away with a double murder. Karma is a BITCH!! This lowlife rat bastard is exactly where he should be... An eternal dirt nap.:poop:
  18. Chuck Leeper

    Need New Front Rotors - What is best?

    Change them. Or you may suffer a break in the break line....
Top