Search results

Great to deal with. Quick response. On point with updates and item status. Thanks, Mike Sent from my iPad using Tapatalk

I have a GEN II asking $240 2 Extender Extreme G chips for sale. Both are set up for 60 pound injectors (one is for alky and one is for non alky) asking $45 each Casper’s Gen2 harness (Brand new never used) $95 Serial cable (Brand new never used) $15 LS1 MAF $75 All prices plus shipping

I need to change some things around on the C100 (Bulkhead connector) Body side. Most pins are the same, Except for. (Need Change/Mod) This is what engine harness needs A7 Tach to Dash B4 Fan Relay PWR C6 Pwr to Fuel inj/fuel pump (I may have since was 4.3L FI) D4 CCCI Spark Pwr PNK/BLK (EST)...

Looking for the c to c u-joint dim.? 85 El Camino hybrid LC2, 200R4, 8.5” GN rear Originally 4.3L fuel injected. Somebody installed a 305 v8 w/700R4 long tail (30.5”) 7.5” Rear, driveshaft is 58.25” c to c, already to short. Thanks, Mike

How much fuel is being displaced by M1 Alky M15 nozzle 155psi against 30psi boost? So 125psi M1 Alky M15 nozzle flow rate? I have 60# Inj. Like know how much my duty cycle is lowered by Alky? Thanks, Mike

I have a Scanmaster G W/Powerlogger with android device (Samsung S7). When i connect (Bluetooth) and display dashboard all the Data is way off or not showing at all? Even in Real time things are way off. I am using SCMG_BT_001a.adx file. Dashboard is ADX file default. I have included 2 logs...

Will the frame mounts from G-body work on an X-Body? Where is the best place to find Buick v6 X-body mounts? Thanks, Mike

Looking for HD wastegate 21psi+ (Garrett 1011-144)? Stock style appearing. TA Let me know what you have with price. Thanks, Mike

Hi, Looking for the 84/87 Calpak chip with holder. Calpak 16036503 Calpak 16036504 Thanks, Mike

Would the motor mounts from a 1975 Buick 3.8 work on a 109 block. I am thinking about a hybrid swap. If the car was an original 1975 Buick 3.8L would a 86/86 motor bolt right in? Thanks, Mike

What size screws are needed to mount the Sender? It's not 4-40. Maybe metric? Thanks, Mike

Will a Chip made for stock ECM High Imp. Inj. Work in a modded ECM for low imp. inj.? Still using the High imp. injectors. Any drawbacks? Thanks, Mike

I have a 1986 GN w/Digital dash. The odometer resets to 3570 every time the car is restarted? I can reset it and it works fine until you turn the car off and restart 3570 again? is there a separate hot all the time wire that may be disconnected? the trip reset & Mph/Kph switch seems to be...

I am testing my alky pump (Razor Kit). W/Razor test kit. With the controller on 8 & Map simulator on 30psi. The gauge fluctuates very fast between 130-150psi (avg. 140psi) So fast you real can not see the needle. Is this normal? Or should it be 140-160psi (avg. 150psi) I usually need to run...

This is a listing for a motor local to me. 109 block bore and honed 30 over. Steel cat stoker crank, k1 rods 6.350, custom j&e pistons. Comp cams custom shaft hydraulic roller 224 224 for 1.65 rockers Comp cams spect this cam and ccombination to be somewhere in the range of 750 hp with about...

Went to Atco Fri 11/15/13 86 GN 70K 11.94 109.8mph 60'- 1.628 Bst- 22# Launch- 5# (Foot Brake) spins with anymore Alky- 7.5 93/Alky Chip- TT5.7 Stock Long Block (New 980 comp springs), Stock MAF, Stock Rear, Stock suspension, 275/60-15 ET streets, 3650lbs W/driver, Dutt neck Stock IC, Closed Ex...

Hi, I am using the tester and seems to be working fine but I can not turn it all the way up without it shutting off. It gets up to about 3/4 turn on the dial. It is creating plenty of spark, almost constant then goes out. All the coils stop. I have to turn it off and wait a moment to...

Hi, Made some runs at Atco Sun 11/10/13. The RPM & IDC show a Spike in my Powerlogger logs. The IDC Spike is in all screens The RPM shows in Graph mode only. The Car felt fine ran great. On Run5 The check engine may have briefly flickered when it happened. Would this be a sign of a going bad...

I have a few Questions. (with photos) 1- What is the spring in the middle of the photo for? 2- Are the 1-2 and 3-4 springs correct? 3- Should there be a rubber seal on the piston? 4- Would this be the proper location for the 1/4" plug on the 3/2 Control valve? 5- What would be the proper...

Hi, I looking for the instructions for CK Performance Shift Kit. I was sent the Kit without the instructions. If someone could PM them to me, I would really appreciate it. I am trying to install the Kit this weekend. Thanks, Mike