Search results

First of all, does anyone has Eric's contact info? There is no email or phone # anywhere on his website. I have a chip I got from Eric years ago. I don't drive my car that much, but my car is basically undrivable when it is over 70 degrees outside. I skips, sputters and stalls when the air...

So I have an 87 GN that is pretty much good to go inside and out. The one thing that bothers me about the car is that it has the dreaded split in the leather right on top of the dash. There is no way to repair it other than taking the dash out of the car and having it completly redone (and...

So it has been going on for years now, but I really am getting tired of not being able to drive my GN when it gets warm outside. I can read my air temp sensor on my scanmaster and any time it gets above 85 degrees or so the car just chokes out. It will idle fine but when you hit the gas the...

So I just got my Weld RT-S wheels on the car (still waiting on one since the weld was cracked and they have to build another one). The drag radials in the back sit at a perfect height. I do need rear springs though as the driver side is sagging. It looks like Kirban has some stock...

My old thread got auto-deleted once it got to page 2 so I'll try again. I'm going with some Weld RT-S 18's on the GN. I was going to go with some 18x9.5 front and 18x10 rear. After talking to Scot at GNS it seems that to run 10's on the back I have to roll fenders. There is no need for me...

Does anyone have a good solution for all the oil leaking out of the valve cover breathers down the side of the block? I have the K+N breathers. They don't have the metal plating that goes around half of the side. Just an open breather. I thought my rear main or valve cover gaskets were...

Hey guys, doing a interior restoration on my 87 that is in really good shape. The one big thing I don't know what to do about is the dreaded split in the top of the dash. Right where the leather comes together on the "stitching". I wanted to see what you guys have done in this situation...

Hey guys, been a looooooong time since I've been on the boards. I want to put either a 17 or 18 weld RTS on the GN. I would like to run a decent size tire on the front- something sticky maybe 255 or so. I would like to run a drag radial on the back, maybe 295 or so. On Weld's website they...

Hey guys, it's been a while since i've been on here. I am putting some love into the Buick again to get her perfect. I have had a T44 on it for a while, but the converter is too loose for a 44. It's a good excuse to go to a 50 or 60 series and make some real power. Here is my setup: T44...

I can't find this anywhere. There used to be a single gauge pod holder that replaced the entire a-pillar piece instead of screwing into it. Does anyone know where I can find it? Thanks!

Hey guys, I saw a complete set of GM body bushings on one of the websites a couple months ago and now I can't find them. I looked on kirban's and cotton's but no dice. Anybody know who carries them? The buick has always been leaning to the driver's side since I have owned it, so I...

Hey Guys, it's been a while since I've been on here for sure. I've got an accumulator ball that is failing and I will be replacing it. My question is where is the best place to pick one up these days? I remember last time I was on here the community opinion was that even if you can find an...

Alright, I'll try to keep this short and sweet so noone will get bored:biggrin: Pump went out, had rock hard pedal and brake light on whenever ignition was on. Replaced brake pump assembly (reman) about a year ago. I only drive it about once a month. Since replacing the pump, the...

What's up guys? I'm an old member who forgot his user name and password. Anyway, I need a race cat for an ATR DP303 downpipe. I have the test pipe that comes with it on there now. I lost my "emissions hookup", so I need to go with something permanent. I had no idea that ATR went out of...