Recent content by baghouse

  1. B

    Exhaust cutout setup recommendations - please share yours!

    I am going to install an exhaust dump with an electric cutout. I have the stock downpipe and no cat. I would be looking for a weld-in WYE and an electric cut out. Can you share you setups with me? What do I need to buy? I want to make sure I buy the right parts!
  2. B

    TPS and IAC replacement

    Ok, I jumped the terminals and pulled a code last night. It was code 15 - coolant temperature sensor circuit (low temp). I do have aftermarket gauges, I do not use the factory sensor. Could that cause high idle?
  3. B

    TPS and IAC replacement

    I've seen a lot of threads about TPS and IAC. Basically mine idles too high. Also, at cold start, the check engine light is on and eventually goes off. It sounds like it's idling around 1000-1200 RPM. I do have a turbotweak chip. And for some reason during this time (while check engine light is...
  4. B

    Good exhaust cutout thread?

    Reply to all - I want noise:) Truth be told it will be "closed" most of the time. Mine is always the quiet one at cruise ins....I want to make an entrance! Also, it's a nice conversation piece.BUT, I want to do it right and CLEAN. Thank you all! Thank you @earlbrown for the PM. Much appreciated!
  5. B

    Good exhaust cutout thread?

    It's official, I want to install an electric exhaust cutout. I tried the search function and there is A LOT of info out there. Can anyone point me to a how-to thread on this topic? I need to know what to buy, how to install, etc. I don't have a CAT, just a pipe welded in place.
  6. B

    How to install TA-49 turbo?

    My TA-49 has arrived! I'm very excited to install this thing! It seems pretty straight forward to install. What do I need to know? It did not come with any instructions. IS THERE A START-UP/BREAK-IN PROCEDURE? What I have: New Ta 49 turbo Copper gasket for Turbo to header connection Oil drain...
  7. B

    Recent oil change concern

    I recently took the turbo off of my GN because I had a little bit of smoke coming out of the exhaust. My Turbo Builder noted that the oil seal was bad but also the bearings had issues and the wheel had rubbed on the housing. When I was changing the oil, for about 1 second, I saw what looked like...
  8. B

    Oil drain pipe install question

    So keep going? Should I use thread tape?
  9. B

    Oil drain pipe install question

    I’m attempting to install a new oil drain pipe from Kirban performance. I’ve screwed it in all the way, I think. However the drain pipe still swivels. Should it swivel? Or should it be super tight?
  10. B

    Kirban intrepid fan question

    Hey! I just installed the intrepid dual fan on my 87 and I am SUPER happy with the results. Before that, I was running the factory fan with the manual controller from Kirban - that way I could toggle between low and high at the flip of a switch. However, I noticed on the intrepid fan, there is...
  11. B

    She's toast...

    I think I spun a bearing over the weekend and took out the turbo too. I changed the oil the night before and got on her pretty hard on the interstate. The temp went up (200 degrees) and the oil pressure went down:( Here is a video of the aftermath...
  12. B

    Kirban CAI question

    Anyone?
  13. B

    Kirban CAI question

    My next upgrade is going to be an intake. I like the Kirban design because it looks like it keeps the filter closer to the fresh air. Can someone post a picture of one installed? I can't tell if it replaces the whole system or not (meaning the stock flex tube). Did you notice a difference in...
  14. B

    What vacuum line is this and where can I find it?

    I went with 3/8 fuel injection hose - good as new! Thank you all of the help! I didn't realize how massive the vacuum leak was. The old line was hard as a rock. The car actually ran better on cold start!
Top