|
 |
 |
 |
 |
 |
 |
 |
|
|||||||
|
Welcome to the TurboBuick.Com forums. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact contact us. |
 |
|
|
LinkBack | Thread Tools | Display Modes |
September 29th, 2007, 05:31 PM
|
|||
|
|||
|
Tranny Pressures
What are good pressures to see at 1000 rpm minimum TV and 1500 rpm at max TV? Is there another good way to check TV pressure?
__________________
Joe Reif Jr. Paola, Kansas 2008 Can-Am Renegade 800 CVT beast 2007 Harley Davidson Road King FLHPI SE 103" 2005 Chevy Silverado 3500...Bombed Oil Burner 1987 Turbo-T...light blue exterior/dark blue interior 84k miles Chip programming by: Eric Marshall @ www.turbotweak.com Meth injection by: www.alkycontrol.com My email:pdq6cyl@midwest-connections.com     
|
|
September 29th, 2007, 06:25 PM
|
|||
|
|||
|
Another question. Should the pressures be any different after putting some miles on a new rebuild?
__________________
Joe Reif Jr. Paola, Kansas 2008 Can-Am Renegade 800 CVT beast 2007 Harley Davidson Road King FLHPI SE 103" 2005 Chevy Silverado 3500...Bombed Oil Burner 1987 Turbo-T...light blue exterior/dark blue interior 84k miles Chip programming by: Eric Marshall @ www.turbotweak.com Meth injection by: www.alkycontrol.com My email:pdq6cyl@midwest-connections.com
|
|
October 1st, 2007, 03:35 PM
|
|||
|
|||
|
Psi
Joe just seen this post
Check the pump rotor to see if its a 13 vane. Reason I say is I pulled my front pump due, to a whining noise, and the rotor was worn. It was grinding on the shaft it surrounds making a high pitch wine. I could see the shiny wear markings. Bruce (@PTS) recommends to use a 10 vien due to the 13 viens being weaker. Something to consider if you pull it to inspect.. Also if I am not mistaken your R pressure should be much higher with min TV. Your P & N should be the about the same (50-75 psi) but manual D1 D2 and R should be 115-140 psi @ 1000rpm. HTH Mike Banas 
__________________
Joe Reif Sr. Lenexa, KS jarsr48@hotmail.com New Combo this year for my 1986 GN: girdled 109 block bored .030 over, 210/215 Comp Cams roller, Harland Sharpe 1.55 roller rockers, 70 mm T/B and Hemco, ported OE intake & 8445 heads, PTE 70GTQ turbo, 83lb injectors Walbro 340M pump, Alky Control dual meth injection, Ol' School ATR front mount IC, Chips by Eric Marshal 10.90 @ 124 mph 1.61 short time 1999 Regal GS 14.80 @ 93 mph (bone stock) MY SON'S TR IS FATSER/QUICKER THAN MINE! In His Dreams Only !! 
|
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| What"s The Pressures | cnoble64 | Transmission Talk | 5 | August 31st, 2007 06:15 AM |
| Turbo 400 pressures | lazaris | Transmission Talk | 19 | February 7th, 2005 04:48 PM |
| A/C Pressures | 1QUIK6 | General Turbo Buick Tech | 11 | August 29th, 2004 07:42 PM |
| Freon Pressures? | scottyb | General Turbo Buick Tech | 2 | June 14th, 2004 06:38 PM |
| Nos pressures | turbowrenchhead | General Turbo Buick Tech | 2 | July 7th, 2003 09:13 PM |
Linear Mode
