4.1 block

Discussion in 'Before Black (non-SFI) Tech' started by mikemcvaney, Jan 18, 2012.

Page 1 of 3

  1. mikemcvaney Member

    Message Count:
    363
    Offline
    Picked up a 4.1 today still need to drop off at machinist to check block no money down not a bad deal.
    mikemcvaney, Jan 18, 2012
    #1

  2. Haterade Adsense



  3. charlief1 Just another kinky six

    Message Count:
    15,867
    Offline
    You're a lucky bum. :biggrin:
    charlief1, Jan 19, 2012
    #2

  4. Ken Adams Member

    Message Count:
    157
    Offline
    I recently picked up two of the 484's and one of the 291 castings. Plan to keep the 291 for a future build
    Ken Adams, Jan 19, 2012
    #3

  5. ek02 Member

    Message Count:
    145
    Offline
    I'm looking for a 4.1 with a standard bore. A 484 block would be fine with me. Want to sell one Ken?
    ek02, Jan 20, 2012
    #4

  6. Ken Adams Member

    Message Count:
    157
    Offline
    Buyer would be required to pick up engine, I will not ship. I'm located in Missouri
    Ken Adams, Jan 20, 2012
    #5

  7. ek02 Member

    Message Count:
    145
    Offline
    I'm in Miami, Fl. Too far to go. UPS can ship a bare block as frieght, but bolting it to a pallot, shrink wrapping, and getting it there can be a pain. Thanks anyway.
    ek02, Jan 21, 2012
    #6

  8. Ken Adams Member

    Message Count:
    157
    Offline
    ek02 thank you for your interest
    Ken Adams, Jan 21, 2012
    #7

  9. Nick Micale Well-Known Member

    Message Count:
    5,251
    Offline
    I just had a 4.1 block shipped to me via Fedex Ground. It was wrapped with cardboard and secured with shrink wrap.

    Since it was well under the 150# limit for Ground delivery, shipping cost was not very expensive. :)
    Nick Micale, Jan 21, 2012
    #8

  10. charlief1 Just another kinky six

    Message Count:
    15,867
    Offline
    Have you considered using Greyhound? I know they'll do shipping as well and it's usually cheaper than the normal lines.:)
    charlief1, Jan 21, 2012
    #9

  11. usetaboost SAY CAR RAMROD!!

    Message Count:
    5,181
    Offline
    Ken are those complete or just blocks?
    usetaboost, Jan 21, 2012
    #10

  12. Ken Adams Member

    Message Count:
    157
    Offline
    One has been disassembled but all parts are there and the other has not been touched
    Ken Adams, Jan 21, 2012
    #11

  13. usetaboost SAY CAR RAMROD!!

    Message Count:
    5,181
    Offline
    how much for the assembled one?
    usetaboost, Jan 21, 2012
    #12

  14. Ken Adams Member

    Message Count:
    157
    Offline
    $275 You pick up
    Ken Adams, Jan 21, 2012
    #13

  15. mikemcvaney Member

    Message Count:
    363
    Offline
    I use greyhound all the time you can send a complete quarter panel with inner and outerwhelhouses across the country for under 150 thats cheap
    mikemcvaney, Jan 21, 2012
    #14

  16. usetaboost SAY CAR RAMROD!!

    Message Count:
    5,181
    Offline
    Whoa, don't want one that bad
    usetaboost, Jan 21, 2012
    #15

  17. jdpolzin Well-Known Member

    Message Count:
    6,287
    Offline
    Thats a good price!
    jdpolzin, Jan 22, 2012
    #16

  18. usetaboost SAY CAR RAMROD!!

    Message Count:
    5,181
    Offline
    You're 6 hrs closer, you should go buy it-NOW!
    usetaboost, Jan 22, 2012
    #17

  19. usetaboost SAY CAR RAMROD!!

    Message Count:
    5,181
    Offline
    That's more than what cores go for in the jy
    usetaboost, Jan 22, 2012
    #18

  20. Ken Adams Member

    Message Count:
    157
    Offline
    The turbo crank and bare block should be worth that and likely more. And let's not forget about the 4-barrel intake, heads, rods, and pan. Surely these items would fetch some $$$ also
    Ken Adams, Jan 22, 2012
    #19

  21. Ken Adams Member

    Message Count:
    157
    Offline
    usetaboost, have at it man,purchase all the jy 4.1 cores you can find.
    Ken Adams, Jan 22, 2012
    #20
Page 1 of 3


Share This Page

^ Top