|
 |
 |
 |
 |
 |
 |
 |
|
|||||||
|
Welcome to the TurboBuick.Com forums. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact contact us. |
 |
|
|
LinkBack | Thread Tools | Display Modes |
October 4th, 2001, 09:00 PM
|
|||
|
|||
|
Can you bend MDF??
http://cgi.ebay.com/ebaymotors/aw-cg...120258&r=0&t=0
from what i can see is that this sub box is made from 3 pieces of board ,but can I bend MDF?? or should I make a box similar to this but with 2 angles instead of three     
|
|
October 4th, 2001, 09:47 PM
|
||||
|
||||
|
You can bend it slightly but not enough for what you are wanting to do, it will break before you get it to the curvature like the one in the pic. You can build a box like that with only 2 angles but you will have to put 2 or 4 drivers in it, 3 drivers would not look right.
__________________
1986 Buick Grandnational MODS: 17" x 8" Billit Centerline "Champ 800's" wrapped in 225/45 Nitto 450s, Bell Tech 2" dropped front spindles, High flow cat/dual 2.5" diameter mandrel bent pipes and Flowmaster Delta Flows with dumps in front of rear axle, '87 GN grille, Polished aluminum mass air flow pipe with K&N on a 150,000 plus mile stock unopened motor.
|
|
October 7th, 2001, 05:04 AM
|
||||
|
||||
|
Are you trying to bend 3/4" MDF? Do you have a table saw? You can cut 1/4" slits to where you want to bend it and reinforce with resin, fiberglass, ect....
__________________
87 Buick Grand National Limit GT6131E, PTE FMIC, 70mm Accufab TB/PTE Plemun, JC power plate and pulleys, RJC boost controller, 65lbs Mototrons, 3.5" Big Mouth cold air kit, ATR 3" downpipe w/ATR external wastegate, ATR 3" dual exhaust, MSD Dis-4HO, Art-Carr #16930 3200 non-lock TC, CAS fuel pressure regulator, Walbro 340 hot wired, Scanmaster 2, QA1's, H&R sway bar, Eibach springs, Air bags. 17" T11's w/315 in the rears! New times 4/1/06 1/4 et 11.38@117.56 mph 1/8 et 7.10@97.57 mph 04 Ford Mustang GT GNRA Member #47 www.imagestation.com/members/HI87GN TURBO BUICK MEMBERS ***BEWARE*** OF BUYING OR SELLING TO MEMBER JUSA6! HID kits for sale http://www.turbobuick.com/forums/par...ml#post1505931
|
|
October 7th, 2001, 05:05 AM
|
||||
|
||||
|
BTW, I think that box is pre made from MTX.
__________________
87 Buick Grand National Limit GT6131E, PTE FMIC, 70mm Accufab TB/PTE Plemun, JC power plate and pulleys, RJC boost controller, 65lbs Mototrons, 3.5" Big Mouth cold air kit, ATR 3" downpipe w/ATR external wastegate, ATR 3" dual exhaust, MSD Dis-4HO, Art-Carr #16930 3200 non-lock TC, CAS fuel pressure regulator, Walbro 340 hot wired, Scanmaster 2, QA1's, H&R sway bar, Eibach springs, Air bags. 17" T11's w/315 in the rears! New times 4/1/06 1/4 et 11.38@117.56 mph 1/8 et 7.10@97.57 mph 04 Ford Mustang GT GNRA Member #47 www.imagestation.com/members/HI87GN TURBO BUICK MEMBERS ***BEWARE*** OF BUYING OR SELLING TO MEMBER JUSA6! HID kits for sale http://www.turbobuick.com/forums/par...ml#post1505931
|
|
October 7th, 2001, 04:06 PM
|
|||
|
|||
here....
Flexible MDF sheeting available at Outwater Plastics www.outwater.com catalog is free or call 800.631.8375
__________________
- Dan Goldstein - 1998 Honda Prelude
|
|
| Thread Tools | |
| Display Modes | |
|
|
Thanks as always
Linear Mode
