Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Donations
Top donors
Your donations
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
New profile posts
Search profile posts
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
THensley's latest activity
T
THensley
replied to the thread
Part number there is a WIX filter that is longer than stock for extra capacity that I used to use, does anyone have the part number I misplaced it?
.
I do run the 51036, and as stated above I probably change oil and filter often enough the extra filtering probably has no filtering...
Today at 12:14 AM
T
THensley
reacted to
~JM~'s post
in the thread
Part number there is a WIX filter that is longer than stock for extra capacity that I used to use, does anyone have the part number I misplaced it?
with
Like
.
Wix 51036 is what I have. Wrote it on a piece of tape stuck to the oil shelf in the garage.
Today at 12:04 AM
T
THensley
replied to the thread
Pro Gear double roller timing chain set *NEW*
.
If Dan used this its good stuff
Tuesday at 1:37 AM
T
THensley
replied to the thread
I was so close
.
My favorite goto For NTP is Loctite 567 and with 1/8 -1/2 NTP you can get 1/2-3/4 turn and maybe a full turn from finger tight. It is...
Tuesday at 1:27 AM
T
THensley
replied to the thread
I was so close
.
ask your local industrial bearing house or bolt house for a small .25 oz bottle that will probable give it to you.
Monday at 10:18 PM
T
THensley
replied to the thread
I was so close
.
please confirm your OE has 1/8 NTP as pictured and not 5/6 inverted flare, If someone changed the OE cooler its posable to not be NTP...
Monday at 9:49 AM
T
THensley
replied to the thread
I was so close
.
Yes on a OE
Sunday at 10:58 PM
T
THensley
replied to the thread
I was so close
.
you are correct ,But the OE is NTP Im about 99% sure. It would be almost imposable to get a 5/6 inverted flare 90 to bottom and seal at...
Sunday at 9:22 PM
T
THensley
replied to the thread
I was so close
.
if I remember correctly those fittings are NPT on a OEM radiator. Loctite has a product 545, it will seal a pipe thread that you cut get...
Sunday at 7:58 PM
T
THensley
reacted to
Chuck Leeper's post
in the thread
What did you use?
with
Like
.
Pipe wrench.........
May 9, 2024
T
THensley
reacted to
pacecarta's post
in the thread
Radiator Install
with
Like
.
flip clip nut and install on rad top plate, seperate the washered nut from the stud install fan using the stud , then slide ac camp...
May 7, 2024
T
THensley
replied to the thread
4" Cold air kit from TURBO REGAL CUSTOM PARTS
.
that a valid ? some people become so frustrated with these cars they may set for 20 years tell they get the courage to tackle some of...
May 7, 2024
T
THensley
replied to the thread
Has anyone installed a Bosch Iboost brake system in a Buick?
.
is this for your G body?
May 6, 2024
T
THensley
replied to the thread
AC Question
.
Yes your correct, but OP said it is cycling , This would indicate some gas is in the system and no contamination has entered. As for...
May 2, 2024
T
THensley
replied to the thread
AC Question
.
The gas has escape some where. But a quick can might get you past the summer heat or it could be 30 bucks that disappears in 2 days. It...
May 2, 2024
Members
Top